Interior & Trim

Dave.C · Post by **Dave.C** » Fri Jun 19, 2009 20:04

Greetings, Hi Im Dave, had my Excel for a couple of years now. Started attacking the interior. Leathers looking good so far. However I'm struggling with the dash & surround, I can not see how to remove it. I've just requested the parts manual,hopefully that will provide some assistance. Anyway any advice would be welcome. Many thanks

Dave.C · Post by **Dave.C** » Tue Jun 30, 2009 19:21

Hi all trying to renovate my tired interior (Excel87), have completed most of the leather.

I am struggling big time removing the dash. Left & right sides are free & mobile but the centre area will not shift & I have removed the centre screw fixing at the top of the dash, have I missed something? I would be so grateful for some advice.

johnf · Post by **johnf** » Tue Jun 30, 2009 20:08

Have you removed the centre console screws etc. If you get access to the online parts manual it will help enourmously. I did this job last year its not as bad as it looks.

Sooty · Post by **Sooty** » Wed Jul 01, 2009 08:14

Dave see your PM I have sent a reply. I think its your Pulsert, M6, Binacle to Centre console Sec 14.05B parts manual.
Wayne

Pete Boole · Post by **Pete Boole** » Wed Jul 01, 2009 12:39

There are three M6 studs below the front edge of the binacle (nearest the bottom of the windscreen and attached to the binacle itself). The nut on the stud nearest the centre-line of the car is really hard to get to if the "climate control" panel is still in. Have a look there.

Pete

Dave.C · Post by **Dave.C** » Wed Jul 01, 2009 21:43

Thank you all for your help. Got the three at the top including the well hidden bugger. But please how do you deal with the Pulsert M6 before I loose my sanity lol. CHEERS

Sooty · Post by **Sooty** » Thu Jul 02, 2009 07:33

Dave
Removal as I remember was quite easy as you just unscrew using the extension tube. The bugger is getting it back in place. Mine is now in my box of Lotus bits in the garage.
Wayne

Dave.C · Post by **Dave.C** » Thu Jul 02, 2009 12:31

Greeting and cheers Wayne. I've tried unscrewing via the tube but it is so
soft that it just folds on itself, unless I'm missing something. I have even tried
sliding a tight fitting alan key to turn without success.

Pete Boole · Post by **Pete Boole** » Thu Jul 02, 2009 19:16

So that's what a Pulsert M6 is!! Now I know which bit you're having trouble with. If it doesn't come undone with the bit of tube (what a rediculous design) the only way is to remove the dash and binacle together I would think - you can then turn it upside down to work on it.

Pete

Dave.C · Post by **Dave.C** » Fri Jul 03, 2009 15:19

Hi all, what fum I've had. The pulsert wouldn't play so it said hello to a hack saw & is now no more; what a bizarre fixing. Anyway dash is almost out, just the air vent on drivers side to disconnect. Again thankyou all so much for your assistance. Hopefully on the road by the end of July, keep fingers crossed.

Pete Boole · Post by **Pete Boole** » Fri Jul 03, 2009 18:22

Well done!

Are you taking any before-and-after photos?

Pete

Dave.C · Post by **Dave.C** » Fri Jul 10, 2009 18:18

Greetings Pete,
apologies for the delay been tied up at work. Have & will continue to take pics. Haven't worked outhow to display themon here.

P.O.D. · Post by **P.O.D.** » Sat Jul 11, 2009 02:20

Hi Dave.C

see this link for how to post pictures. http://www.lotusexcel.net/phpbb/viewtop ... =16&t=1639

you can also use any web picture hosting site , I use Picasa 3

P.O.D.

The Lotus Grand Tourers

Interior & Trim

Interior & Trim

Re: Interior & Trim

Re: Interior & Trim

Re: Interior & Trim

Re: Interior & Trim

Re: Interior & Trim

Re: Interior & Trim

Re: Interior & Trim

Re: Interior & Trim

Re: Interior & Trim

Re: Interior & Trim

Re: Interior & Trim

Re: Interior & Trim