Page 21 of 30

Re: New comer - Progress (edit)

Posted: Tue Mar 23, 2021 19:00
by hodders
966 "likes" to date and 80 responses, mainly along the lines of "my dad had one of those" but also pointing out that the symbols below the Excel are those of Harry's head-up display (HUD).

Re: New comer

Posted: Wed Aug 04, 2021 11:11
by Hawaiis0
In June 2013 :-
Hawaiis0 wrote: Mon Dec 29, 2014 21:19 -5 degrees and no blower fan! Not good with 130 miles to drive. Found a rather nasty looking fuse - 20 amps too! I hope the cause is high resistance corrosion and not the resistor pack. Fuse replaced 4 speed blower back in action.


Image
Move forward 8 years......

Image

They don't make fuses to last nowadays -- :roll: Anyone got a nail? :shock:

Re: New comer - Progress (edit)

Posted: Wed Aug 04, 2021 15:44
by Excel SA
I'd be giving the fan motor a good clean and service - seem to recall mine was full of rubbish.

When the nail gets red hot it may melt the whole fuse box!

Neil.

Re: New comer - Progress (edit)

Posted: Wed Aug 04, 2021 20:44
by Hawaiis0
The root cause appears to be a misaligned spade in the the fuse box.

The fuse was locked in the recess by one spade, the other side riding outside the other spade but touching to make contact.

This then chattered causing the heat.

I will be cutting the wires out and fitting a stand alone fuse carrier just for that circuit. I'm not changing the whole module just for one.

Re: New comer - Progress (edit)

Posted: Thu Aug 05, 2021 06:02
by Excel SA
Don't worry about the fan then!

That was done on my car, bumped the fuse up to 20 amps from 5 I think.....helpful that, might be why the red light in the passenger door melted.

Neil.

Re: New comer - Progress (edit)

Posted: Sun Nov 14, 2021 14:57
by Hawaiis0
Brake refresh today with new Green stuff pads. Make sure you get your monies worth :oops: :roll: :lol:

Image

Re: New comer - Progress (edit)

Posted: Sun Nov 14, 2021 14:59
by Hawaiis0
Quick and easy system on the Hi Spec calipers. Took longer to jack the car up than to change the pads.

Image

Re: New comer - Progress (edit)

Posted: Sun Nov 14, 2021 16:53
by Pete Boole
Thousands of miles left on those!! :wink:

Pete

Re: New comer - Progress (edit)

Posted: Sun Nov 14, 2021 20:49
by bash
Are you holding those pads between your bum cheeks ?

Re: New comer - Progress (edit)

Posted: Sun Nov 21, 2021 18:35
by Hawaiis0
I had lost the rubber bung from the aerial mount.
Whilst doing some sealing with a silicon gun tube, I had to clear the old sealant from the nozzle.
This gave me an idea :!:
It normally can be removed when dry, whole in perfect form of the nozzle. A nice tapered wedge.
I could then gauge the diameter against the hole and make a perfect silicon plug :)

Re: New comer - Progress (edit)

Posted: Sun Nov 21, 2021 19:05
by Pete Boole
You'll be competing with Neil to mould your own bushes soon!! :D

Pete

Re: New comer - Progress (edit)

Posted: Sun Mar 13, 2022 18:45
by Hawaiis0
Saw a Ferrari yesterday.

A bit tatty, no brakes and would not start.

Image

Re: New comer - Progress (edit)

Posted: Sun Mar 13, 2022 20:19
by Pete Boole
Italian rubbish! :lol: :lol: :lol:

Pete

Re: New comer - Progress (edit)

Posted: Mon Mar 21, 2022 19:09
by Hawaiis0
The wife knows!

It's very quite and there's no tea!

Re: New comer - Progress (edit)

Posted: Tue Mar 22, 2022 14:00
by Pete Boole
I can hear the shouting from here!! :lol: :lol:

Pete